// Frontera Technical Support • View topic - M.O.T advisory Spongy break pedal
   
 

M.O.T advisory Spongy break pedal

banter general discussions etc

M.O.T advisory Spongy break pedal

Postby mochelle on Wed Apr 12, 2017 5:26 pm

Had an advisory on the sheet "Spongy Break pedal" anyone else had this or got any advice for me please had a Mechanic lookout it but he claims it feels ok ? The jeep is a Frontera 2.2 petrol SWB also had corrosion on the break lines they have now been changed!
mochelle
Newbie
Newbie
 
Posts: 1
Joined: Mon Mar 20, 2017 11:32 pm
Location: Anglesey
Model: 2.2i Sport Olympus 3dr
Registration Year: 2002/51
Vehicle Name: Lara too
Modifications: spot lights
Region: North Wales



Re: M.O.T advisory Spongy break pedal

Postby Fronterror on Wed Apr 12, 2017 6:59 pm

I've had this before, bleed the brakes and if it's like the 2.5td there is a 5th bleed nipple around the rear axle which i think bleeds another reservoir but someone can correct me and enlighten me as to what it actually is. Could be the tester was just expecting more from them but it's easy enough to do even if there is no difference after
Fronterror
Apprentice Frontera engineer
Apprentice Frontera engineer
 
Posts: 63
Joined: Wed Aug 31, 2016 6:49 pm
Model: 2.5 TDS 5dr
Registration Year: 1998/R
Region: South East



Re: M.O.T advisory Spongy break pedal

Postby ghosthunter on Thu Apr 13, 2017 4:03 pm

You have to bleed the load proportion valve first before you bleed the rears and lastly the fronts. The valve is visible above the rear axle on the nearside. It has an arm sticking out and a spring attached to it connecting to the axle. There's a bleed nipple on the valve and you must bleed this first. You may need to bleed the whole lot several times to make sure all the air is out. Bleed everything in the correct order and when done go and do it again.
Bag 'O' Sh*te No1 2.2 petrol 2000
Bag 'O' Sh*te. No2 3.2 petrol 1998
User avatar
ghosthunter
frontera God
frontera God
 
Posts: 890
Joined: Thu Feb 05, 2009 9:47 am
Location: RHYL Wales and COIN near MALAGA Spain
Model: 3.2 V6 5dr
Registration Year: 1998/S
Vehicle Name: Bag 'O' Sh**e No2
Region: North Wales



Re: M.O.T advisory Spongy break pedal

Postby snapper on Sat Apr 15, 2017 10:13 am

What ghosthunter said.

However I would say to get a large bottle of brake fluid (Personally I buy the 5ltr containers) a brake bleeding kit, the right sized ring spanner for the bleed nipples (don't use an adjustable) and considering it is a two handed job unless you really know what your doing and have the right gear to do it single handed get a friend to help.

Not knowing how much of the brake lines were replaced the chances are the fluid has not been changed since the vehicle was new and certainly not during the last 5 years so the fluid in there will probably be contaminated with moisture as well as air in which case I would recommend a full fluid change to include a flush hence getting enough to do the job.

Expect the bleed nipples to be beyond tight and they WILL be at risk of snapping so be very careful when undoing and don't force the issue, clean everything around the bleed nipple twice before opening and then again just to make sure.

Do not re-use the fluid that comes out and please dispose of it correctly via the local re-cycle and not down the sink!

Finally, if the bleed nipples are over tight make sure you can source and replace a calliper easily in case you snap one off. Milners do sell them.

Any doubt, send it to the garage.
This posting may have been helpfull, on the other hand probably not... Either way, I may have had drink when posting it in which case it's probably not as helpfull as it could have been

Work safe, and remember all technical problems can be resolved with a hammer, the trick is knowing where to hit it and how big a hammer to use (I often find it may also help to have a spare bit in the shed to replace the bit you have just mullered ;) )

Work in Progress (or not as the case may be) I give you.... 'O-no' the truck.

Comments on 'O-no' the truck may be left here

Work in Progress (or not as the case may be) I give you.... 'Truck'

Comments on 'Truck' the truck may be left here

Owning a 2.8 is a hobby in it's self...
User avatar
snapper
Lord frontera
Lord frontera
 
Posts: 2188
Joined: Sat Mar 27, 2010 1:32 am
Location: Oxfordshire, Brize Norton.
Model: 2.8 TDI 5dr
Registration Year: 1995/N
Vehicle Name: Truck and O-no
Modifications: -
2.8 TD LWB - Truck:
Side Steps Removed
EGR, Birds Nest & Both Butterfly Valves Removed
Particulate Filter removed and pipe welded in
Safari Snorkel fitted
Trooper Flywheel & Clutch fitted
Trooper LSD Rear Axle fitted
Winch Bumper & Winch fitted
3.1 Engine Fitted
2" Suspension Lift

2.8 TD LWB - O-no:
Standard, for now.

2.5 Volvo 850 Saloon:
Standard

Volvo XC70 D5 SE Lux (185bhp)
Standard
Region: South East




Return to General discussion

Who is online

Users browsing this forum: No registered users and 18 guests

 
   


cron