// Frontera Technical Support • View topic - Trooper hub removal
   
 

Trooper hub removal

banter general discussions etc

Trooper hub removal

Postby lee771 on Tue Feb 28, 2017 3:08 pm

Hi all
Can any one advise me on procedure to remove both front hubs and 98 Trooper 3.1?
Want the whole lot off including discs ecthe

Any advise would be great
User avatar
lee771
Fronty Engineer
Fronty Engineer
 
Posts: 142
Joined: Sat Mar 14, 2015 6:46 pm
Location: telford shropshire
Model: 2.0i Sport 3dr
Registration Year: 1996/N
Modifications: +2" suspension
33 12.5 15s
-32 offset steel rims
Landrover arch extension
Region: Midlands



Re: Trooper hub removal

Postby ghosthunter on Wed Mar 01, 2017 2:21 pm

First off the wheel.
Next remove the six bolts holding the hub cover.....10mm I think.
Remove the cover marking its position so to refit the same.
You should now see the end of the drive shaft and its retaining circlip.
Remove the circlip and any shims behind it....keep safe.
Now remove the six bolts holding the hub. Get somebody to push the brakes as they are around 40 foot pounds.
Withdraw the hub.
Remove the brake caliper and tie up out the way.
Now you should see a plate with lots of holes and 3 screws 120 degrees apart.
Remove the screws......they are there to lock the plate and stop it turning.
When removed you will be able to tap the plate anti clockwise and then unscrew it by hand.
Remove the plate underneath, can be awkward because of the grease and stubby fingers.
But as the assembly is free you can retrieve it after you remove the main hub.
Grasp the disc both sides and pull the hub/disc off the spindle.
Retrieve the plate and inner race of the outer bearing.
You can now work on the hub/disc assy..ie change disc ,bearings and seals.
It sounds more complicated than it is and when you start it is a logical sequence.
Have fun :dance: :dance:
I'm pretty sure I haven't missed anything but if I have someone will jump in and correct
Bag 'O' Sh*te No1 2.2 petrol 2000
Bag 'O' Sh*te. No2 3.2 petrol 1998
User avatar
ghosthunter
frontera God
frontera God
 
Posts: 865
Joined: Thu Feb 05, 2009 9:47 am
Location: RHYL Wales and COIN near MALAGA Spain
Model: 3.2 V6 5dr
Registration Year: 1998/S
Vehicle Name: Bag 'O' Sh**e No2
Region: North Wales



Re: Trooper hub removal

Postby Fatbaz on Wed Mar 01, 2017 7:18 pm

Hi
All pretty much the same as a Fronty really..........seeing as one is a copy of the other I suppose they must be much the same........who copied who I don't know.

Regards

Stuart
Remember, keep the greasy side down!
Fatbaz
frontera God
frontera God
 
Posts: 754
Joined: Sun Sep 23, 2007 3:44 pm
Location: Cosgrove, Northampton
Model: 2.8 TDI Sport 3dr
Registration Year: 1996/P
Modifications: Extended axle and transmission breathers.
Suspension lift curtesy of TJM +2 springs
+2 Rough country shocks curtesy of Llama 4X4
Mitsibushi L200 wheel (16x7 10mm offset)
Hankook RT03 285/75R16
Long wheel base light conversion
50mm body lift
Twin Electric rad fan conversion
Roof mounted waffle board rack with boards
Light bar with Lights and CB ariel mount
Custom built winch bumper to suite Body lift
Tmax 11000 lbs winch with external and incab controls.
Aisin Manual Hubs
Region: Midlands



Re: Trooper hub removal

Postby jmc on Thu Mar 02, 2017 9:07 pm

Had to withdraw the front hub as I couldn't fit the new lower ball joint without pulling the up the driveshaft .
I was terrified as I had read posts of it being very complicated and has to be taken all apart. Mine didn't, it just all came out in one lump. With my heart in my mouth I put it down thinking this can't be right I've broken it. I carried on and got the new lower ball joint in place. I had kept an eye on which way round everything was so put the assembly back and got the circlip in place.
The 4x4 seems to work so I assume I put it back ok.
User avatar
jmc
Lord frontera
Lord frontera
 
Posts: 1428
Joined: Sat Jan 06, 2007 5:39 pm
Location: whitstable,kent.
Model: 2.5 TDS 5dr
Registration Year: 1998/R
Modifications: 2.5 lwb dark green with a two inch bodylift.Steel lockers over wheel arches to store stuff in.
2.3 blue.new leaf springs.changed drop down tailgate with rear swing door to take spare wheel.now not on the road awaiting repairs.
Region: South East



Re: Trooper hub removal

Postby RatCav on Sat Mar 04, 2017 10:08 pm

Same as Frontera as they both use Isuzu parts.
ImageImage

My members ride For Banshee the Trooper : viewtopic.php?f=46&t=34626

My members ride for Leeloo the Lotus Edition viewtopic.php?f=46&t=60154

Deceased

My members ride for Brenda the Bighorn : viewtopic.php?f=46&t=54771
User avatar
RatCav
Super Trooper
Super Trooper
 
Posts: 5577
Joined: Thu Mar 19, 2009 11:20 am
Location: Preston, Lancs.
Vehicle Name: Banshee
Modifications: Its a Frontera that is heavily disguised as a Mk.1 LWB Isuzu Bighorn 2.8TD Lotus Edition.
Hi-roof modification.
EGR valves and birds nest of vacuum pipes removed.
Front Manual Locking Hubs.
Rear Limited Slip Differential.
Yota Surf steels, with custom paintjob. (cheers Gregster)
33x12.5" R15 General Grabber AT 2's.
+2" suspension lift.
+3" body lift.
Cat 1 Thatcham approved alarm.
Irmscher wheel arch flares.
Full body restoration/respray. (cheers Gregster again!)
Region: North West




Return to General discussion

Who is online

Users browsing this forum: Bing [Bot] and 4 guests